Audio-Technica VM 530 EN/H
Prices incl. VAT plus shipping costs
in stock - immediate delivery
- Article number: 204023
The AudioTechnica VM 530 EN / H cartridge is equipped with a nude ™ elliptical tip and a pre-mounted cartridge holder AT-HS10.
The AudioTechnica VM 530 EN cartridge is equipped with an elliptical tip (diamond nude). Audio-Technica's Dual Magnet Design, patented internationally, reproduces the structure of a cut tip.
You can choose with (AudioTechnica HS 10 cartridge holder pre-mounted or without cartridge holder).
- Cantilever conical aluminum
- Para-toroidal coils improve efficiency
- Intermediate shielding plate between left and right channels reduces crosstalk
- Low resonance hard polymer housing
AudioTechnica's patented dual magnet design principle is based on vinyl record reproduction.
Instead of a single large magnet, two V-shaped magnets are precisely aligned to accurately scan the right and left channels of the sides of the stereo groove. In this way, a VM system provides exceptional channel separation, extended frequency response, and superior sampling capacity.
System with para-toroidal generator
Para Toroid coils improve the efficiency of the generator and provide outstanding linearity, since only a small part of the magnetic flux can escape due to the continuous symmetrical design of the magnetic circuit (parasitic flux), in addition, the permeability of the magnetic cores is optimized by the stratified core structure.
Medium shielding plate for reduced crosstalk
The central permalloy shielding plate allows efficient separation of the left and right channels and eliminates electrical crosstalk up to 40 dB. This corresponds approximately to the actual crosstalk values of a recording groove.
Technical characteristics
- Principle: MM
- Frequency response: 20 hz-25 kHz
- Channel separation: 27 dB
- Channel balancing: 1.5 dB
- Output voltage: 4. mV
- Vertical reading angle: 23 °
- Supporting force: 1.8 / 2.2g
- Recommended support force: 2g
- Tip: Elliptical Nude
- Tip Size: Nude 0.3 x 0.7mm
- Assembly: integral
- Cantilever: aluminum
- Compliance: 14 x 10-6cm / dyne
- Coils: para-toroidal, PCOCC conductors
- Mobile magnet: VM Double magnet
- Load impedance: 47 Kohms
- Load capacity: 100-200 pF
- Mass cartridge: 6.4g
- Height: 17.3 mm
- Fixing: 1/2 inch
- Replacement Diamond: VMN 30 EN
| Typ | VM Type |
| Befestigung | 1/2” centres |
| Frequenzbereich | 20 - 25,000Hz |
| Kanaltrennung | 27dB (1kHz) |
| Kanalbalance am Ausgang | 1.5dB (1kHz) |
| Ausgangsleistung | 4.0mV (1kHz, 5cm/sec.) |
| Vertikaler Abtastwinkel | 23˚ |
| Vertikaler Auflagekraftbereich | 1.8 – 2.2g (2.0g standard) |
| Nadelschliff | Elliptical Nude |
| Nadelabmessungen | 0.3 x 0.7 mil |
| Schaftform der Nadel | Nude Round Shank |
| Nadelträger | Aluminium Pipe |
| Spulenimpedanz | 2,700Ω (1kHz) |
| Statische Nadelnachgiebigkeit | 35 x 10-6 cm/dyne |
| Dynamische Nadelnachgiebigkeit | 8 x 10-6 cm/dyne (100Hz) |
| Empfohlene Lastimpedanz | 47,000Ω |
| Empfohlene Lastkapazität | 100 – 200pF |
| Gewicht | 6.4g |
| Abmessungen | 17.3 (H) x 17.0 (W) x 28.2 (L) mm |
| Ersatznadel | VMN30EN |
| Beiliegendes Zubehör | Cartridge installation screws 5mm ×2 and 10mm ×2, Washer ×2, Hexagon nut ×2, Non-magnetic screwdriver ×1, Brush ×1, Lead wire set ×1 |
